manualshive.com logo in svg

Siemens EH675TK11E, Repair Instruction, Page: 58 / 113

Share
Download
Siemens EH675TK11E Repair Instruction Download Page 58

 
 

206_58300000141095_ara_en_k.doc – 04.10.a 

Seite 58 von 113 

Power regulation according to the type and size of the pot 

 

 

Warning! 

 

The power supplied according to the size of the pot with IH5-I is less 
than with IH4 (ind IV advanced). 

 

P

IV Adv

IH5

plate

min

100%

75%

15%

P

IV Adv

IH5

plate

min

100%

75%

75%

15%

 

 

Pot Diameter

Pot Diameter

P

IH5 

< P

IH4

P

IH5 

< P

IH4

 

 

 

By taking into account the material and size of the pot, the level of 
power supplied can be reduced and even shut off so as to avoid 
excessive currents.  
 

FP 

enhanced

FP 

enhanced

 

For example, for a pot with a base diameter identical to the size of the 
inductor coil and of a material with good electro-magnetic properties, 
the FP enhanced obtained gives us maximum power. If we have no 
pot, the FP enhanced is nil and the power supplied is nil. The display 
flashes. 
If the pot is not of a suitable diameter and its composition is not 
suitable for our induction cooker, the FP enhanced calculated by our 
technology will be so low that the power supplied will be nil. 
 

Summary of Contents for EH675TK11E


















































































































Reviews:

No comments