Siemens EH675TK11E Repair Instruction Download Page 47

Page: 47 / 113

206_58300000141095_ara_en_k.doc – 04.10.a

Seite 47 von 113

3.13.3 Oval inductors support

The aluminium base for oval inductors is designed with:

•

Clips for fixing the position of the oval inductor

•

4 holes placed in the middle for NTCs connections

•

2 holes placed on the left side for inductor connections.

We must take into account that these inductors have a fix position
above the aluminium base. It must be checked, that the inductors
don´t move.

3.13.4 New control concept

3.13.4.1 Flexible Mode

•

What is Flexi mode? It is the activation of the whole surface

marked with red rectangle. After, it is made a search, in order to
know where is the pot and activate only the necessary coil.

•

If flexi mode is activated, there is the same power level for all

coils/zones/cookware!

•

If flexi mode is not activated, it can be set two independent

power levels,

1 power level setting for coil 1 and 2
and other power level setting for coil 3 and 4.

The number from the oval in red, is the selected power in the zone

Summary of Contents for EH675TK11E


















































































































Search results

Summary of Contents for EH675TK11E

Reviews:

Siemens EH675TK11E, Repair Instruction, Page: 47 / 113

Search results

Summary of Contents for EH675TK11E

Reviews: