manualshive.com logo in svg

Siemens 7ME305, Operating Instructions Manual, Page: 32 / 124

Share
Download
Siemens 7ME305 Operating Instructions Manual Download Page 32

Safety measurements

WARNING

Qualified personnel

Only qualified personnel may carry out work on the electrical connections.

WARNING

Use in hazardous locations

Special requirements apply to the location and interconnection of sensor and transmitter. 
See Installation in hazardous area (Page 12) 

WARNING

Danger of electric shock!

Never install the device with the mains voltage switched on!

The version for power supply 19 to 30 VDC may only be connected to SELV or PELV circuits.

Cable specifications

• Use cables with a cross section of at least 1.5 mm2 and double or reinforced insulation for the 

power supply.

• Lay heat-resistant cables if high temperatures can occur on the housing, eg due to 

conduction of heat by the sensor/metering tube. Lay the cables so that they do not come into 
contact with the hot sensor/metering tube.

• Lay signal cables separately from cables with voltages > 60 V.

• Use cables with twisted wire pairs.

• Earth transmitter housing.

• Cables used for connection must have diameters fitting the glands.

• Use shielded cables for the outputs

• Compare data on rating plate with local power supply.

Connecting

SITRANS FUS060 with PROFIBUS PA

32

Operating Instructions, 09/2021, A5E02225054-AD

Summary of Contents for 7ME305





























































































































Reviews:

No comments