SHP Laboklav ECO 135 User Manual Download Page 27

Page: 27 / 29

LABOKLAV Eco 80 / 135

User Manual

9. User replaceable accessories and spare parts

Spare part

Drawing number

Article number

Lid seal Laboklav ECO 80

Laboklav 80 ECO

50-05-10000-003

Lid deal Laboklav ECO 135

Laboklav 135 ECO

50-05-10000-005

Magnetic valve Laboklav ECO

Laboklav 80 + 135 ECO

50-05-10000-014

Filter 0,3

m / 99,5%

Laboklav 80 + 135 ECO

40-0719-142-014

Paper rolls for printer

Laboklav 80 + 135 ECO

50-05-30001-195

Carbon stripe for Printer

Laboklav 80 + 135 ECO

50-05-30001-183

Printer for Laboklav ECO

Laboklav 80 + 135 ECO

20.0000.000.300

Basket Ø 39,5cm x 30cm

Laboklav 80 ECO

30.0400.000.300

Bucket Ø

Laboklav 80 ECO

30.1400.000.300

Basket Ø

Laboklav 135 ECO

30.0500.000.300

Bucket Ø

Laboklav 135 ECO

30.1500.000.300

Basket with closed bottom Ø 39,5cm x 25cm Laboklav 80 ECO

30.2400.000.250

Basket with closed bottom Ø

Laboklav 135 ECO

30.2500.000.250

Condensate collection canister

Laboklav 80 + 135 ECO

20.0000.000.500

10. Description of safety devices

The steam sterilizer is equipped with different safety devices. The safety devices protect the user

against injury and safe the sterilization process. Mechanical and electronic safety devices are built

in and realize in sum a safety concept with different safety functions.

- Protection against over pressure – If control board is measuring a chamber pressure of

more than 345 kPa absolute pressure (2.45 bar relative pressure) an alarm is generated

(including error message) and the heating function is switched of and the unit breaks the

program. With 2.8 bar relative pressure the safety valve is opening and chamber pressure is

reduced mechanically! The steam is blowing into the housing contact with the steam is not very

dangerous because it is saturated after blowing out.

Attention: To check the safety valve a special program can be implemented that is bridging

the safety functions of over pressure protection. This program will be implemented on special

order by the customer only! Blowing off the safety valve in the condition that the housing I not

opened can damage the electronic board!

- Protection against opening the chamber while over pressure is inside – The device has

a built in thermo locking function. The device opens the thermo lock when pressure is low only.

The pressure is checked by pressure sensor and an additional pressure switch that detects

normal pressure. The opening mechanism is calculated to open when chamber pressure is low.

These 3 safety functions give good protection against opening while pressure in chamber is

high.

- Protection against opening the chamber while temperature of liquids is too high – One

part of the thermo locking system is the measurement of the temperature inside liquids by the

reference sensor. The device is unlocking the lid in liquid programs when temperature is lower

than programmed removing temperature is reached only. The flask where the reference sensor

Summary of Contents for Laboklav ECO 135






























Search results

Summary of Contents for Laboklav ECO 135

Reviews:

Related manuals for Laboklav ECO 135

Brands by name

Popular brands

SHP Laboklav ECO 135, User Manual

Search results

Summary of Contents for Laboklav ECO 135

Reviews:

Related manuals for Laboklav ECO 135

Brands by name

Popular brands