![background image](http://html.mh-extra.com/html/sharp/up-5700/up-5700_service-manual_373332034.webp)
·
Error stop/Continue/1 Pass
Selection is made among Error Stop/Continue/1 Pass in case
of an error.
·
Test start ? [Yes/No]
Selection is made between Yes/No of test start.
Check content
Read is made for the cylinder range, the head number, and the
sector number areas set in the above.
When read test is completed in the set range, it is counted as 1
pass.
In case of an error during the above test, retry is repeated up to
the set number of retry. Every time when an error occurs in retry
up to the set number of retry, error logging is made. Logging is
made for HD and DRAM.
When "Error Stop" is set in the test condition setting, if an error
occurs during the above test, the error display is shown and the
test is interrupted. Press the space key to resume the test.
When "Continue" is set, even if an error occurs, the error display
is made but the test is not stopped.
When "1 Pass" is set, a series of tests is made only once and the
test is stopped.
Display
Select desired items at positions of @. (@ is not displayed on the
screen.)
(On the above screen, the thick figures are selected, and the thick
figure values are selected.)
On the above screen, when pass count is counted up (when point
is counted up to the upper limit set in the cylinder range setting,
the pass count is counted up by 1.), and if the error counter of all
error items are not counted up (remaining as 00000), the test is
OK.
Terminating method
The methods to interrupt, resume, and terminate the test are
same as (2) Sequential read.
6) HD Dump Test
[Test conditions setting]
·
Cylinder No. [0
~
inmost cylinder]
A certain cylinder No. to be displayed is set.
·
Head No. [0
~
final head]
A certain head No. to be displayed is set.
·
Sector No. [1
~
final sector]
A certain sector No. to be displayed is set.
Check content
The sector set in the above is displayed on the screen in the unit
of 256byte.
Hex data and ASCII characters are displayed.
By key operation, the following 256 byte data or previous 256byte
data can be displayed.
Display
The physical address is set at position of @. (On the above
screen, the thick value is set.)
On the above screen, the first-half 256 byte at 000 cylinder, 00
head, and 01 sector is displayed.
Press the page down key to display the second-half 256 byte.
(When the page down key is pressed on the above screen, the
second-half 256byte at 000 cylinder, 00 head, and 01 sector is
displayed.)
Press the page up key to display the first-half 256byte.
Terminating method
Press Esc key to return to the menu screen of previous (1).
7) Error Information Display
Check content
Error information stored in the inmost area of the HDD is dis-
played.
When the hard disk test is executed, error information stored in
the error information storing area is displayed.
The inmost cylinder, 0 head, and 1 sector
~
6 sector are read to
be displayed.
Target Sector Read test
@Cylinder range ?
[000 XXX] = 000-XXX
(XXX is displayed by checking the
inmost cylinder.)
@Head count ?
[0 XX] = 0
(XX is displayed by checking the
final head.)
@Sector count ?
[0 XX] = XX
(XX 8s displayed by checking the
max. sector.)
@Retry count ?
[0 4] = 0
@[Errorstop continue 1pass]
@Test Start ? [Yes No]
Pass count = XXXXX
Test Point = CCC : HH : SS (Cylinder: head; sector)
Error Kinds
Drive not ready XXXX
Bad controller XXXX
Compare error XXXX
ESC : Exit SPACE : Stop or Start
Details of error are displayed.
HD Dump test
@Physical address ? [CCC. HH. SS] = 000. 00. 01
The first hslf sector
000 : HHHH......HHHH-HHHH......HHHH : AAA......AA
(100)
PGDN : forward PGUP : back SPACE : Start ESC : Exit
:
010 : HHHH......HHHH-HHHH......HHHH : AAA......AA
(110)
:
0F0 : HHHH......HHHH-HHHH......HHHH : AAA......AA
(1F0)
:
020 : HHHH......HHHH-HHHH......HHHH : AAA......AA
(120)
:
:
4 – 18
Summary of Contents for UP-5700
