Sharp MX-B401 Page 766 Operation Manual Download | Manualshive

Page: 766 / 837

background image

7

INSTALLATION REQUIREMENTS

Improper installation may damage this product. Please note the following during
initial installation and whenever the machine is moved.

1. The machine should be installed

near an accessible power outlet for
easy connection.

2. Be sure to connect the power cord

only to a power outlet that meets
the specified voltage and current
requirements. Also make certain
the outlet is properly grounded.

• For the power supply

requirements, see the name plate
in the lower left corner of the left
side of the machine.

Connect the machine to a power
outlet which is not used for other
electric appliances. If a lighting
fixture is connected to the same
outlet, the light may flicker.

3. Do not install the machine in areas

that are:

• damp, humid, or very dusty
• exposed to direct sunlight
• subject to extreme temperature

or humidity changes, e.g., near
an air conditioner or heater

• poorly ventilated.

4. Be sure to allow the required space

around the machine for servicing
and proper ventilation.

5. The machine includes a built-in

hard drive. Do not subject the
machine to shock or vibration. In
particular, never move the machine
while the power is on.

17-23/32"
(45 cm)

11-13/16"
(30 cm)

11-13/16"
(30 cm)

mxb401_us_saf.book 7 ページ２００９年１月７日　水曜日　午後３時３３分

«
...
764
765
766
767
768
...
»

Summary of Contents for MX-B401






































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MX-B401

Brand: QMS Pages: 160

Brand: QMS Pages: 110

Brand: QMS Pages: 158

Brand: CAB Pages: 144

870 - SuperScript B/W Laser Printer

Brand: NEC Pages: 52

SuperScript 1800

Brand: NEC Pages: 8

Brand: TallyGenicom Pages: 3

Brand: IBM Pages: 334

Brand: IBM Pages: 428

Brand: IBM Pages: 316

Brand: IBM Pages: 210

Brand: TE Connectivity Pages: 2

Brand: TE Connectivity Pages: 2

WorkCentre 7800 series

Brand: Xerox Pages: 14

WORKCENTRE 7775

Brand: Xerox Pages: 15

WORKCENTRE 7775

Brand: Xerox Pages: 24

WORKCENTRE 7755

Brand: Xerox Pages: 252

WORKCENTRE 7755

Brand: Xerox Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands