Sharp MX-B401 Page 68 Operation Manual Download | Manualshive

Page: 68 / 837

background image

1-29

BEFORE USING THE MACHINE

Contents

TRAY SETTINGS FOR TRAY 1 TO 4

LOADING PAPER AND CHANGING THE PAPER SIZE

A maximum of 500 sheets of paper from size 5-1/2" x 8-1/2" to size 8-1/2" x 14" (A5 to A4) can be loaded in trays 1 and 2.
A maximum of 500 sheets of paper from size 7-1/4" x 10-1/2" to size 8-1/2" x 14" (B5 to A4) can be loaded in trays 3 and 4.

1

Pull out the paper tray.

Gently pull the tray out until it stops.
To load paper, go to step 3. To load a different size of paper, go
to the next step.

Do not pull hard on the tray. This may cause failure.

2

Adjust the guide plates A and B by
squeezing their lock levers and sliding
them to match the vertical and
horizontal dimensions of the paper to be
loaded.

The guide plates A and B are slidable. Slide each guide plate
while squeezing its lock lever.

• Be sure to place the guide to match the size of the paper. If the guide is not placed correctly, paper skewing or

misfeeds may occur.

• The loaded paper should not go higher than these protrusions.

3

Fan the paper.

Fan the paper well before loading it. If the paper is not fanned,
multiple sheets may feed at once and cause a misfeed.

When handling paper, take care not to cut yourself on the edges of the paper.

A

B

«
...
66
67
68
69
70
...
»

Summary of Contents for MX-B401






































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MX-B401

Brand: Panasonic Pages: 155

Brand: Panasonic Pages: 160

Brand: Radio Shack Pages: 62

imageRUNNER ADVANCE DX C478iZ

Brand: Canon Pages: 208

imageRUNNER ADVANCE DX C477iFZ

Brand: Canon Pages: 92

Aficio SP C420DN

Brand: Ricoh Pages: 4

Brand: SEWOO Pages: 17

VersaLink C405/N

Brand: Xerox Pages: 256

Brand: Cycjet Pages: 26

Brand: Oki Pages: 20

DRYPRO Model 793

Brand: Konica Minolta Pages: 156

201021 - P 330N Photo Printer

Brand: Olympus Pages: 79

Multi-Font NX-2415

Brand: Star Micronics Pages: 134

Fast T-Jet Blazer Pro

Brand: Screen Print & Inkjet Pages: 138

Brand: SII Pages: 85

SignJet JS310 Series

Brand: GRAPHTEC Pages: 83

Brand: Tandy Pages: 83

Brand: Xerox Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands