LEARNING THE RADIO CONTROL CODE
The circuit board incorporates a dual-channel radio receiver at 433.92 MHz, which allows to control the gate at a
distance via micro switch radio controls from the OG/02, OG/04 range and self-learning radio controls from the
OG/62, OG/64, OG/28, OG/48, OG/52, OG/54, OG/82/1 and OG/84 range. Both of the channels are used
exclusively to control the gate. In particular channel 1 of the radio receiver acts from start, while channel 2 acts from
the pedestrian.
DELETING CODES IN THE MEMORY
The deleting of all radio codes memorised is carried out by pressing and holding the A (SET) key until the DL10
LED switches off (about 10s) without sending any radio code.
!
ATTENTION: - before using a minitransmitter, perform the programming procedure.
- a maximum of 32 codes can be memorised for start c 32 for pedestrian
control (other combinations are not possible for example 40 start + 24 pedestrian
etc.). Below find two examples of codes that can be memorised:
- example A:
- example B:
32 self-learning minitransmitters
OG/62, OG/64, OG/28, OG/48, OG/52,
OG/54, OG/82/1 and OG/84 as
start
control (e.g. left button) +
32 self-
learning minitransmitter
OG/62, OG/64, OG/28, OG/48, OG/52, OG/54,
OG/82/1 and OG/84 as pedestrian control (e.g. right button)
31 self-learning minitransmitters
OG/62, OG/64, OG/28, OG/48, OG/52,
OG/54, OG/82/1 and OG/84 as
start
control (e.g. left button) +
1
minitransmitter with micro switches
OG/02, OG/04 as
start
control (the
other OG/02 and OG/04 do not have to be memorised just set the micro
switches in the same sequence as that memorised) +
31 self-learning
minitransmitters
OG/62, OG/64, OG/28, OG/48, OG/52, OG/54, OG/82/1
and OG/84 as
pedestrian
control (e.g. right button) +
1 minitransmitter
with micro switches
OG/02, OG/04 as
pedestrian
control (the other
OG/02 and OG/04 do not have to be memorised just set the micro
switches in the same sequence as that memorised)
!
DA
L
19
65
Page 15/18
LEARNING START CODE
- With the control unit powered and the gate closes, press key A once (SET) to enter programming. The DL10 LED
starts to flash to indicate that the control unit is in the programming state.
- Press the minitransmitter button (e.g. on the left), which wants to act as start control and hold it down until the
DL10 LED switches off. The control unit has memorised the radio code received and automatically leaves
programming, setting itself for normal functioning.
- Repeat the procedure if several minitransmitters must be memorised.
LEARNING PEDESTRIAN CODE
- With the control unit powered and the gate closed, press and hold key A once (SET) to enter programming. The
DL10 LED starts to flash to indicate that the control unit is in the programming state.
- Hold down key A (SET), Press the minitransmitter button (e.g. on the right), which wants to act as pedestrian
control and hold them down until the DL10 LED switches off. The control unit has memorised the radio code
received and automatically leaves programming, setting itself for normal functioning.
- Repeat the procedure if several minitransmitters must be memorised.
12 3
4 5
6 7
8 9
10
12 3
4 5
6 7
8 9
10
!
MODIFY THE FACTORY
CONFIGURATION TO PREVENT
UNDESIRED CONTROLS
CONFIGURATION OF MICRO SWITCHES ONLY IN THE CASE OF OG/02 AND OG/04 MINITRANSMITTERS
Only if OG/02 and OG/04 radio controls with micro switches are used, before performing learning of the codes on
the receiver, the factory configuration of the micro switches must be modified to prevent undesired controls
ATTENTION before starting first programming or deleting the radio controls, temporarily
disconnect the antenna to prevent the receiver from acquiring other signals during this phase,
which may cause incorrect functioning of the automation. Re-connect the antenna when the
procedure has ended.
:
K
IT
/A
9
I
E
