background image

1 Safety 

 
 

4

 

SCHMIDT

®

 ServoPress 605-660 

– V1.1

 

1  Safety 

The  press  is  designed  and  built  in  accordance  with  the  valid  safety 
regulations  and  state-of-the-art  methods  and  is  tested  for  function  and 
safety. The press is/will be a component of the press system. 

  

To ensure operational safety, note: 

 

Chapter "Designated use" 

 

Chapter "Organizational measures of the owner" 

 

Chapter "Residual risks" 

 

Chapter "Standards and regulations" 

  

Independently of the indications specified in this manual, the current country 
specific regulations regarding work safety and health protection are valid. 

  

1.1  Designated use 

The press can be used as follows: 

 

As  component  in  a  SCHMIDT  manual  workstation  during  pressing 
processes with manual loading and unloading. 

OR

 

 

As  part  of  a  press  system  together  with  SCHMIDT  components  for 
automation.  In  this  case,  the  press  system/tool  has  to  be  designed  in 
such a way that is not possible to reach into the hazard zone. 

  

Any  other  use  for  any  purposes  other  than  those  described  above  is 
considered contrary to its designated use. The manufacturer cannot be held 
liable for damages resulting from this. 

Please  do  not  make  any  changes  to  the  components.  The  manufacturer 
cannot be held liable for damages resulting from this. These changes are at 
the sole risk of the owner. 

  

Designated use also includes 

 

compliance with the documentation and 

 

compliance  with  the  inspection  and  maintenance  instructions  of  the 
manufacturer 

  

1.2  Organizational measures of the owner 

The press may only be operated in technically perfect condition.  

  

The  instructions  concerning  start-up,  operation  and  maintenance  described 
in this manual must be observed. 

This manual must be stored within easy reach at the workplace. 

  

The  persons  responsible  for  the  work  on  the  press  must  have  read  the 
manual and, in  particular,  chapter  "1  Safety" before starting  work. This also 
applies to persons who work on the machine only occasionally. 

Manual 

Personnel 

Summary of Contents for ServoPress 605-660































Reviews: