Schmidt PressControl 3000 Operator'S Manual Download

Page: 53 / 56

11 Maintenance and servicing

SCHMIDT

PressControl 3000 – V1.3

Make a note of both values.

Start the return stroke.

Select the "System Options" system function key.

In the "System Options" submenu, select the "Calibrate analog Inputs"

command.

Select the "Analog Input 1".

Enter the noted value (in kN) into the "Value Machine" parameter.

Enter the noted value (in kN) into the "Value Reference" parameter.

Select "Calculate & Save" using the arrow key.

Confirm the entry by pressing the "Enter" key. The control calculates

the new calibration value from the two entered values and displays the
result.

CtrON

CtrOFF

...

Servic

Force Calibration

Calibration 1.0000

Value Machine 1.0000

Value Reference 1.0000

Calculate & Save

Calibration Init

Figure 11-3: "Force Calibration" submenu

Subject the force sensor again to a load.

Compare the measured value of the reference measuring system with

the measured value of the machine.

Repeat the calibration process if the values do not coincide.

The calibration affects the value of the force offset.

After the calibration, check whether the value has changed.

After a large change has taken place, set the force offset again. For

more information on setting the force offset, please see chapter
"11.1 Setting the force offset".

If there are large calibration errors, you can reset the calibration value to "1".

Select the "Calibration Init" command.

When using the optional analog output 2 to measure quality-relevant
dimensions, regular inspections or calibrations should be made.

Proceed as described at "Analog input 1".

Entering

measured values

Calculating

calibration value

Checking calibration

Resetting

calibration value

Summary of Contents for PressControl 3000

























































Search results

Summary of Contents for PressControl 3000

Reviews:

Related manuals for PressControl 3000

Brands by name

Popular brands

Schmidt PressControl 3000, Operator'S Manual

Search results

Summary of Contents for PressControl 3000

Reviews:

Related manuals for PressControl 3000

Brands by name

Popular brands