Schmidt PressControl 3000 Operator'S Manual Download

Page: 37 / 56

8 Further integrated functions

SCHMIDT

PressControl 3000 – V1.3

Servic

...

CtrOFF

CtrON

40.432 mm

2138 N

Reached stroke :

Reached force :

21 pcs

4 pcs

17 pcs

Quantity :

Quantity nok :

Quantity ok :

30.000 mm

Returnstroke at stroke:

2-Hand-Release

Machine ok.

PC-DEAC

Dataset 1

( )

Figure 8-2: View of "Output 1" including the note "PC-DEAC"

When operating the control on an external PC using SCHMIDT

ControlTool

software, a press stroke is only possible if the PressControl 3000 is
connected to ControlTool. If there is no connection, the stroke will be
blocked.

Select the "Data Input" system function key.

Select the "PC on/off" parameter.

Enter the value "1". To switch the function off again, enter the value "0".

As long as no connection has been established to the PC, the stroke
remains blocked. In addition, the control displays "! PC not ready !".

Servic

...

CtrOFF

CtrON

40.432 mm

2138 N

Reached stroke :

Reached force :

21 pcs

4 pcs

17 pcs

Quantity :

Quantity nok :

Quantity ok :

30.000 mm

Returnstroke at stroke:

! PC not ready !

SPC-OFF

PC-OFF

Dataset 1

( )

Figure 8-3: View of "Output 1" including the note "! PC not ready !"

Configure the press system in the SCHMIDT

ControlTool software

(see section "Define press unit" in the "User Manual - SCHMIDT
ControlTool - Part 1").

Establish the connection (see chapter "4.1 Establishing a connection to

the control" in the " User Manual - SCHMIDT

ControlTool - Part 1").

Select the “Data Input” system function key.

Select the "SPC on/off" parameter.

Configuring the press

SCHMIDT

ControlTool

Establishing a

connection

Switching on the SPC

Summary of Contents for PressControl 3000

























































Search results

Summary of Contents for PressControl 3000

Reviews:

Related manuals for PressControl 3000

Brands by name

Popular brands

Schmidt PressControl 3000, Operator'S Manual

Search results

Summary of Contents for PressControl 3000

Reviews:

Related manuals for PressControl 3000

Brands by name

Popular brands