Scantech DC-100 Programming Manual Download Page 69

Page: 69 / 86

used to check the correctness of the data.

If check digit is “None”, the scanner will transfer the code data normally.

None Check But No Transmit Check Digit

Check and Transmit Check Digit

Code Length Limit

The scanner can only read the the code length within the limited of Plessey the

limit is from the minimum to maximum value (including the minimum and maximum

value), the unit is character. If the length of Plessey is out of the limit, the scanner will

not be able to read or transmit the code.

Read “Minimum Length” to set the minimum length of code.

Read “Maximum Length” to set maximum length of code.

Plessey Maximum Length Plessey Minimum Length

The maximum length value of any type of 1D code is not more than 255. If the

maximum length is shorter than the minimum length, the scanner can only read this

two length of code; if the maximum length is equal to minimum length, the scanner can

only read the code of this length.

This length is the length of the code itself, not including prefix/suffix, tailed suffix,

AIM-ID,CODEID.

Summary of Contents for DC-100























































































Search results

Summary of Contents for DC-100

Reviews:

Related manuals for DC-100

Brands by name

Popular brands

Scantech DC-100, Programming Manual

Search results

Summary of Contents for DC-100

Reviews:

Related manuals for DC-100

Brands by name

Popular brands