Scantech DC-100 Programming Manual Download

Page: 14 / 86

Sensitivity is the sense degree that the scanner detects the surrounding change

environment in decoding. Users can set the sensitive according to their own using

environment to improve the decode efficiency.

High Sensitivity Medium Sensitivity

Low Sensitivity Custom Sensitivity

In auto-sensor mode, the sensitivity is set from 0-255, the smaller value, the

higher sensitivity level.

For Example: set the sensitivity of 10 as below:

、

Read “Custom Sensitivity”

、

Read the number

“

”

“

”

、

Save setting

Command Trigger Reading Mode

In this mode, need to control the trigger to read the code.

Command Trigger Reading Mode

Decoding Status Prompt

If decode is not success, the scanner will output a prompt as F that means the

reading is not success, and output a prompt as S that means the reading is success.

Disable Decoding Status Prompt Enable Decoding Status Prompt

Summary of Contents for DC-100























































































Search results

Summary of Contents for DC-100

Reviews:

Related manuals for DC-100

Brands by name

Popular brands

Scantech DC-100, Programming Manual

Search results

Summary of Contents for DC-100

Reviews:

Related manuals for DC-100

Brands by name

Popular brands