Scantech DC-100 Programming Manual Download

Page: 12 / 86

reading code till the user press the trigger button again. When defaulted, it is not

allowed to repeat reading the same code.

Auto Reading

In auto reading mode, the decoding time can be set from 0~255s, when the

decoding time is set 0, it means no limit time for reading code.

Decoding Time

When scan the enable repeat the same code, the scanner will read one code and

automatically read the next code; and it will stop reading code till you press the trigger

button.

When scan the disable repeat the same code, the scanner will read one code and

automatically read the next code. If the next code is same as the previous one, the

scanner will be waiting status, and decode again till the decoding same code time is out.

When the code is not repeated, the scanner will read the code continuously and stop

reading code after press the trigger button.

Enable Repeat the Same Code Disable Repeat the Same Code

Decoding Same Code Time

The interval unit is 100ms, set from 0.1~25.5s. If interval is set as 0, it means no

limit time for decoding same code.

For example: the interval is set as 5000ms, the setting is as below:

、

Read “Enable Repeat the Same Code”

Summary of Contents for DC-100























































































Search results

Summary of Contents for DC-100

Reviews:

Related manuals for DC-100

Brands by name

Popular brands

Scantech DC-100, Programming Manual

Search results

Summary of Contents for DC-100

Reviews:

Related manuals for DC-100

Brands by name

Popular brands