SBC PCD7.L79 Series User Manual Download Page 18

Page: 18 / 72

Saia-Burgess Controls AG

Manual for PCD7.L79xN room controllers

│

Document 27 / 602

N02 │ 2013-11-27

Procedure for the temperature calibration on commissioning

Commissioning instructions

2-5

Carry out only if necessary:
2) Dynamic calibration (Register 29)

This setting depends on the connected thermal valves type and quantity and on the

installation-conditions. This calibration is not mandatory and can be performed at spe-

cific room constellation in which the measurement accuracy is not sufficient.

a) Connect the thermal valves and activate (over the setpoint)

the PWM outputs to 100 %.

b) After 30 minutes the temperature has to be measured near to the lower air slots

and to compare with the measured temperature of the controller.

c) When the displayed temperature of the controller is too high, then it is possible

to set a higher stage for the “dynamic correction” (stage 1 up to 5).

Stage Effect

None Without dynamic correction

increase of the dynamic correction

2
3
4
5

Maximum → for several parallel connected valves

Summary of Contents for PCD7.L79 Series









































































Search results

Summary of Contents for PCD7.L79 Series

Reviews:

Related manuals for PCD7.L79 Series

Brands by name

Popular brands

SBC PCD7.L79 Series, User Manual

Search results

Summary of Contents for PCD7.L79 Series

Reviews:

Related manuals for PCD7.L79 Series

Brands by name

Popular brands