SBC PCD7.L79 Series User Manual Download Page 43

Page: 43 / 72

Saia-Burgess Controls AG

Manual for PCD7.L79xN room controllers

│

Document 27 / 602

N02 │ 2013-11-27

Functions, manual output control

Function

3-25

FBox outputs "L79x Room"

“-Occupied, presence”

Parameter for detection of presence.

“-SetPt”, control set point

Actual control set point taking account of any manual interventions and limitations.

“-Temp”, actual value

Actual value as input signal to the two PI controllers for heating and cooling. The

measurement point can be defined via the configuration. (See "Function, settings,

hardware").

“-HeatY”, heating valve

Control of heating valve in in [%].

“-CoolY”, cooling valve

Control of cooling valve in in [%].

“-Err”, error flag

FBox internal output for detecting communication errors. If a transmission with all

telegram repeats fails completely, the FBox disables communication until the next

attempt by the Setup FBox. The retry time is defined in seconds in the Setup FBox

via the internal parameter "Pause after communication error".

A description of the L79x Room FBox settings can be found in the online help for

Saia PG5

Summary of Contents for PCD7.L79 Series









































































Search results

Summary of Contents for PCD7.L79 Series

Reviews:

Related manuals for PCD7.L79 Series

Brands by name

Popular brands

SBC PCD7.L79 Series, User Manual

Search results

Summary of Contents for PCD7.L79 Series

Reviews:

Related manuals for PCD7.L79 Series

Brands by name

Popular brands