Sapling SAP Series Installation Manual Download Page 71

Page: 71 / 82

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA

P. (+1) 215.322.6063
F. (+1) 215.322.8498
www.sapling-inc.com

Web Interface - Log In

Web Interface - Date and Time

Password

- Location where the password is entered. The default password is 6063, but this can be

changed within the settings.

Log In

- When pressed, the program will check the password. If the password is correct, it will grant

the user access to the Web Interface.

Welcome Sign

- Displays the Clock name.

Time

- Displays the clock’s time at the moment the web page was loaded. This information does not

update unless the page is refreshed.

Date

- Displays the clock’s date at the moment the web page was loaded. This information does not

update unless the page is refreshed.

DST

- Displays the current Daylight Saving Time setting.

Analog Clock

S y n c h r o n i z e d C l o c k S y s t e m s

Summary of Contents for SAP Series



















































































Search results

Summary of Contents for SAP Series

Reviews:

Related manuals for SAP Series

Brands by name

Popular brands

Sapling SAP Series, Installation Manual

Search results

Summary of Contents for SAP Series

Reviews:

Related manuals for SAP Series

Brands by name

Popular brands