Sapling SAP Series Installation Manual Download Page 25

Page: 25 / 82

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA

P. (+1) 215.322.6063
F. (+1) 215.322.8498
www.sapling-inc.com

Description

SAP square analog clock

Mounting Piece

(already attached to

clock housing)

Quantity

Picture

Wall Mount Installation - Square Clock

Included in Package

Included in Wiring Kit (A-WK-MTG-1)

#8x1.5 Self-tapping screw

Wall anchor

2 (not used)

PLEASE NOTE:

A user will also have to provide a Phillips-head screwdriver, a small flat-blade screwdriver, a drill with a 1/4 inch drill bit, a pencil, a single

gang box, any equipment needed to install the gang box, at least one CAT5 or CAT6 patch cable, and any additional network cables or devices needed to
provide Power over Ethernet, and a connection to an NTP server.

If any of the items listed in the wiring kit are missing, you may contact your dealer and order a
replacement kit.

Complete the section “Preparing to Install” before mounting the clock on the wall.

Included in Gang Box Kit (A-GB-MK-1)

#6-32x1 screw

#6-19x3/8 screw

Summary of Contents for SAP Series



















































































Search results

Summary of Contents for SAP Series

Reviews:

Related manuals for SAP Series

Brands by name

Popular brands

Sapling SAP Series, Installation Manual

Search results

Summary of Contents for SAP Series

Reviews:

Related manuals for SAP Series

Brands by name

Popular brands