Sapling SAP Series Installation Manual Download Page 47 | Manualshive

Page: 47 / 82

background image

47

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA

P. (+1) 215.322.6063
F. (+1) 215.322.8498
www.sapling-inc.com

Double Mount Installation - Round Metal Clock

Dual-mount pole, including
mounting plate and adapters

#10-32x3/8 green screw

1

1

Description

SAP round analog clock

Mounting Bracket

Quantity

2

2

(not used)

Picture

Included in Package

Included in Double Mount Kit (SAB-4BD-12R-0 or SAB-4BD-16R-0)
(SAB-4BD-12R-0M

or

SAB-4BD-16R-0M)

Included in Wiring Kit (A-MK-QS-1E)

#6-32x1/2 screw

M4-0.5x10

#10x1.5 Self-tapping screw

Wall anchor

4

(not used)

4

(not used)

2

(not used)

2

(not used)

PLEASE NOTE:

A user will also have to provide a Phillips-head screwdriver, a small slot-head screwdriver, a drill with a 1/4 inch drill bit, a pencil, a double

gang box, four wall anchors (must support 50 lbs, #8 screw size, 1.5”(3.8cm) screw length), four #8 screws for the wall anchors, four #6-32x1 screws for
attaching the mounting plate to the gang box, any equipment needed to install the gang box, at least two CAT5 or CAT6 patch cables, and any additional
network cables or devices needed to provide Power over Ethernet, and a connection to an NTP server.

If any of the items listed in the kits are missing, you may contact your dealer and order a replacement kit.

Complete the section “Preparing to Install” before mounting the clock on the wall.

«
...
45
46
47
48
49
...
»

Summary of Contents for SAP Series



















































































Reviews:

No comments

Related manuals for SAP Series

Brand: La Crosse Technology Pages: 11

Brand: La Crosse Technology Pages: 18

Brand: La Crosse Technology Pages: 2

Brand: La Crosse Technology Pages: 2

Brand: La Crosse Technology Pages: 6

Brand: La Crosse Technology Pages: 3

Brand: La Crosse Technology Pages: 12

Brand: La Crosse Technology Pages: 10

Brand: La Crosse Technology Pages: 4

Brand: La Crosse Technology Pages: 8

Brand: ZEBON Pages: 2

Brand: Auriol Pages: 68

Brand: Scott Pages: 2

Brand: Oregon Scientific Pages: 12

Brand: prologue Pages: 40

Brand: GPX Pages: 2

Brand: Somogyi Pages: 12

Brand: Somogyi Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands