Sanwa MT-44, Manual

Page: 63 / 68

６１ ６２
About installing the sensor
Key Assignments Feature List
About insta
lling
the sensor
●
When connecting a sensor to the receiver, replace the connector cover of the receiver top and connect the temperature sensor and RPM sensor.
●
For a connector that does not connect a sensor, cut the dust cover for the receiver to use.
●
Attach the sensor part of the temperature sensor tightly to a subject to measure the temperature.
Since the sensor part is extremely sensitive to temperature, secure the sensor part so that it will not be affected by the ambient air.
●
When installing the RPM sensor, attach the reflective decals onto the point to measure the number of rotations
and fix the RPM sensor so that the sensor part of the RPM sensor is able to detect. When the RPM sensor is
detecting properly, the LED of the receiver lights in green (or goes off).
*The recommended distance between the RPM sensor and the detecting part is 1mm.
●
When the point to measure the number of rotations is black, cut the white reflective decals; when the point to
measure is white, cut the black reflective decals to attach so that the RPM sensor is able to detect them.
Depending on the reflective decals used, the receiver LED lights in green or it goes off when the sensor detects.
●
The RPM sensor uses an infrared system, thus it is sensitive to the sunlight. When the sensor cannot detect properly,
try to protect the infrared sensor from the sunlight.
●
Make sure the cords of the temperature sensor, the RPM sensor and the sensor part are secured so that they will
not touch or will not be pulled into the rotating pars or moving parts of the car.
●
Make sure not to hurt yourself when mounting the RPM sensor and the temperature sensor.
●
If the connector is disconnected due to a vibration during operation, it can cause runaway.
Connect the connector of the receiver, servos and switches securely.
●
Because the receiver is susceptible to vibration, impact and water, make sure to take measures for
vibration-proof and waterproof. Negligence of taking these measures can cause runaway.
●
When installing the receiver, keep the receiver away from a carbon chassis and metallic chassis.
●
If metal parts installed on an RC car touch each other, it can cause noise that affects reception performance and it can cause runaway.
●
Make sure to install a noise killer condenser on the brush motor for electric RC cars. Without a noise killer condenser, it can cause noise and runaway.
●
For R/C System parts such as the transmitter, receiver, servos, FET Speed Controller and transmitter battery, use genuine SANWA products.
*When combining products other than genuine SANWA products, modifying, adjusting or exchanging
parts is done at a place other than SANWA, we do not take responsibility.
About installing the sensor and a compatible receiver (RX-461/RX-462)
Reflective Decals
[When detecting with the Spur Gear]
Infrared Sensor
(Back)
(Sensor Part)
(Sensor Part)
Infrared Sensor
Installation Stay
Installation Stay
Installation Stay
Approx 1mm
[Temperature Sensor Installation Example]
(Back)
Reflective Decals
●W
hen installing the RPM sensor, attach the enclosed reflective decals to the point to measure number of rotations
(e.g.: a pinion gear or spur gear), cut out the sensor attachment stay from a polycarbonate board or aluminum angles and
fix the RPM sensor so that the infrared sensor of the RPM sensor is able to detect. When the RPM sensor is detecting properly,
the LED of the receiver lights in green (or goes off).
*The recommended distance between the infrared sensor and the reflective decals (detecting part) is 1mm.
●
Regarding how to use the enclosed reflective decals for the RPM sensor, cut out white or black reflective decals (about 2mm diameter)
and attach them onto the point to measure the number of rotations so that RPM sensor is able to detect. Depending the color of the
reflective decals, the receiver LED responds differently when the sensor detects. When the reflective decals pass in front of the
infrared sensor, a green LED light is on for white decals and a green LED light goes off for black decals.
*When checking the performance of the RPM sensor, turn on only the power Switch off the receiver side.
If the power switch of the transmitter side is on at the same time, the blue LED will be on when indicating signal is being received.
You cannot check the green light is on/off when the sensor is detecting.
●
The enclosed RPM sensor uses an infrared system, thus it is affected by the sunlight. When the sensor cannot detect properly,
try to protect the infrared sensor from the sunlight.
●
When installing the RPM sensor to a car with a different driving system layout, refer to the following.
●
Attach the sensor part of the temperature sensor
tightly onto the subjected item to measure.
Since the sensor part is extremely sensitive to temperature,
secure the sensor part with a double adhesive tape
so that it will not be affected by the ambient air.
●
Make sure the cords of the RPM sensor, the temperature sensor and the sensor part are secured so that they will not touch or
will not be pulled into the rotating pars or moving parts of the car.
●
Make sure not to hurt yourself when mounting the RPM sensor and the temperature sensor.
RPM Sensor
Infrared Sensor
Temperature sensor
Temperature sensor
RPM sensor
temp.1 : Temp. sensor1
temp.2 : Temp. sensor2
LED
r.p.m. : RPM sensor
Sensor Part
Sensor Part
Sensor Part
Dust Cover
for the Receiver
Sensor Part
Cover the Sensor Part with
double adhesive tape
[Distance between the Infrared Sensor and Reflective Decals (Sensor Part)]
[When detecting with the Pinion Gear]
Key Assignments Feature List
Throttle Trim TRIM-TH
SPD-TH Throttle Speed
SPD-ST Steering Speed
Steering Speed Forward SP-ST-F
Steering Speed Return SP-ST-R
Throttle Speed Forward SP-TH-F
Throttle Speed Return SP-TH-R
Anti-Lock Brake ALB
Anti-Lock Brake Point ALB-PO
Anti-Lock Brake Stroke ALB-ST
Anti-Lock Brake Lag ALB-LG
Offset OFFSET
Anti-Lock Brake Cycle ALB-CY
AUX1 AUX1
AUX1 [Cord 1] AUX1[CD1]
AUX1 [Cord 2] AUX1[CD2]
AUX1 [Cord 3] AUX1[CD3]
AUX1 [Cord 4] AUX1[CD4]
AUX1 [Cord 5] AUX1[CD5]
AUX2 AUX2
AUX2 [Cord 1] AUX2[CD1]
AUX2 [Cord 2] AUX2[CD2]
AUX2 [Cord 3] AUX2[CD3]
Telemetry MAX Clear TE-CLR
AUX2 [Cord 4] AUX2[CD4]
AUX2 [Cord 5] AUX2[CD5]
Timer TIMER
Steering Drive Assistance ASIST-ST
Steering Dual Rates D/R-ST
ーーー
(no assigned feature)
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○
○ ○ ○
○ ○ ○
○ ○ ○
OFF
Throttle Dual Rates D/R-TH
Brake Dual Rates D/R-BR
Steering Curve CUR-ST
Throttle Curve CUR-TH
Steering Curve Rate CU-R-ST
Throttle Curve Rate CU-R-TH
Brake Curve Rate CU-R-BR
Steering Trim
○ ー ー
○ ー ー
○ ー ー
○ ー
ー
ー
○ ー ー
○ ー ー
○ ー ー
○ ー ー
○ ー ー
○ ー ー
○ ー ー
○ ー ー
○ 〇 〇
○ 〇 〇
○ 〇 〇
○ 〇 〇
○ 〇 〇
○ 〇 〇
ー
○ 〇 〇
○ 〇 〇
○ 〇 〇
○ 〇 〇
○ ー ー
○ ー ー
○ ー ー
○ ○ ー
○ ○ ー
○ ○ ー
○ ○ ー
○ ○ ー
○ ー
〇 ○ ー
TRIM-ST
AUX2 Trim TRIM-A2
AUX1 Trim TRIM-A1
AUX1 [Cord 6] AUX1[CD6]
AUX1 [Cord 7] AUX1[CD7]
AUX1 [Cord 8] AUX1[CD8]
AUX1 [Cord 9] AUX1[CD9]
AUX1 [Cord 10] AUX1[CD10]
○ 〇 〇
○ 〇 〇
○ 〇 〇
○ 〇 〇
○ 〇 〇
AUX2 [Cord 6] AUX2[CD6]
AUX2 [Cord 7] AUX2[CD7]
AUX2 [Cord 8] AUX2[CD8]
AUX2 [Cord 9] AUX2[CD9]
AUX2 [Cord 10] AUX2[CD10]
○ 〇 〇
○ 〇 〇
○ 〇 〇
○ 〇 〇
○ 〇 〇
Names of the Features Trim SW1 SW2 Screen Display
Settable
・・・「○」
Not Settable
・・・「－」
NOTE