Trim 4
Trim 3
１９
２０
Usa
ge of e
ach
featur
e
Usage of e
ach
fea
tur
e
Note
● If the linkage is locked for a long period,
it can cause the servo motor breakage.
● Adjust the end point of the steering/throttle linkage before
adjusting dual rates (
P
. 27, 28).
Supplement
Dual Rates [D/R]
● You can adjust rudder angle when operating the steering wheel and throttle trigger to their peak.
To correspond to the RC car or road condition, adjust the rudder angle as you operate.
*You can adjust steering for both right and left at the same time and throttle separately for high
and brake sides. You can also adjust the brake side more precisely than adjusting with EPA.
● Donʼt increase the setting rate of dual rates (D/R) from the condition in which the linkage locks
by operating the steering wheel and throttle trigger.
● You can also adjust more precisely by adjusting dual rates of the throttle side.
*When AUX1/AUX2 are set to CODE5/CODE10, setting change of D/R will not be reflected
to the performance.
1) Select features [ST/TH (H, L)/AUX1/AUX2)
to adjust with the Select key.
2) Determine the feature to adjust with the Enter key
and adjust the setting rate with the multi-select key.
3) Adjust the valus of DUAL RATE by multi-selector.
4) During operation, the steering dual rates can be
adjusted with Trim 3, brake dual rates can be
adjusted with Trim 4. Itʼs possible to assign other
features to Trim 3 and Trim 4 with the key assign trim
feature (P. 52).
*When cancelling a selected feature,
operate the Back button.
○ Setting range: ST/TH-H/AUX1/AUX2
：
0
％～
100
％
TH-L
：
0%
～
120
％
○ Default:
ST/TH/AUX1/AUX2
：
100
％
SETTING
*Make sure that the servos do
not lock to make clicking
sound! Note)
The same for throttle.
DUAL RATE SETTING SCREEN
Steering Dual Rates Selection Screen
● Features to control the speed of the servos used for steering and throttle. By setting, the RC car is not affected even
when doing a sudden operation. On the steering side, smooth corner work becomes possible and on the throttle side,
stable rising from a corner by throttle work with saved power.
* When setting AUX TYPE to [CODE5/CODE10], adjusting the speed feature of the AUX channel does not affect the performance.
* When setting the speed of the AUX channel, do so using steering/throttle as a reference.
●A feature to delay the speed of the steering servos against the steering operation.
Y
ou can set speed for steering
forward and returning individually. For steering operation slower than setting, the speed feature does not work.
1) Select [ST (Steering)] with Up key/Down key.
2) Setting on the forward side [FOR
W
ARD]
Select [FOR
W
ARD] with the Enter key and adjust the
setting value with Up key/Down key.
*When cancelling a selected feature, use the Back key.
○ Setting range: 0
～
-
100
○ Default:
0
3) Setting on the Return side (RETURN]
Select [RETURN] with the Enter key and adjust the setting value with Up
key/Down key.
○ Setting range:
0
～-
100
○ Default:
0
*Adjust during actual operation. When not using the features or when a setting value cannot be determined even after
adjustment, set the value to 0% (linear).
●For driving an RC car, steering operation that suits the movement of the RC car is important and excessive operation
is not recommended. Steering speed can minimize unnecessary operation and enables smooth cornering.
●When steering speed and steering curve are combined, the effect is doubled.
Supplement
● For driving an RC car, throttle operation that suits the movement of the RC car is important and excessive operation
is not recommended. Throttle speed can minimize unnecessary operation and enables smooth performance.
● When throttle speed and throttle curve are combined, the effect is doubled.
Supplement
[ST] Steering Speed
● A feature to slow down the performance speed of the throttle se rvos and delay the response of the speed controller against thr ottle
operation.
Y
ou can set speed for entering throttle (Forward) and returning (Return) individually. The speed feature does not work with
throttle operation slower than the setting. *Setting is only for High side and Brake side cannot be set.
1) Select [TH (Throttle)] with Up key/Down key.
2) Setting on the forward side [FOR
W
ARD]
Select [FOR
W
ARD] with the Enter key and adjust the
setting value with Up key/Down key.
*When cancelling a selected feature, use the Back key.
○ Setting range:
0
～
-
100
○ Default:
0
3) Setting on the Return side (RETURN)
Select [RETURN] with the Enter key and adjust the setting
value with Up key/Down key.
○ Setting range:
0
～-
100
○ Default:
0
*Adjust during actual operation. When not using the features or
when a setting value cannot be determined
even after adjustment, set the value to 0% (linear).
[TH]
Throttle Speed
Neutral
Neutral
End
End
End
Ｎ
Ｎ
FORWARD
RETURN
FORWARD
RETURN
FORWARD
RETURN
Ｒ
Ｌ
Ｈ
SPEED
SETTING
Select Channel by Multi-selector button.
Choose [TH] by selector button.
ENTER
BACK
ENTER
BACK
Usage of each feature
Flashing
Choose [ST] by selector button.
Summary of Contents for MT-44
Page 1: ... 90478 ...
Page 68: ......
