Samsung SRN-1000 User Manual Download Page 78

Page: 78 / 122

78_

menu setup

record option

You can set the recording to stop or overwrite when the HDD is full.

•

Disk End Mode : Select a HDD repetitive recording type.

- Overwrite : If the HDD is full, this will overwrite the existing data and keep recording.
- Stop : If the HDD is full, this will stop recording automatically.

•

Disk End Beep : If you select <

Stop

> for the disk end mode, this button will be active. Specify the use of

beep when the HDD recording ends.

If you check it, the beep will sound on the disk full and the recording stops.

•

Auto Delete : If you check this option, the period list box is active. Specify the deletion period to delete any

earlier data than the specified date. However, you can search for data from the current time to the selected

date.

If you press <

> when you have completed your settings, all the existing data earlier than the specified period will be

deleted automatically. So it is recommend to backup the previous data if necessary for later use.

Summary of Contents for SRN-1000



























































































































Search results

Summary of Contents for SRN-1000

Reviews:

Related manuals for SRN-1000

Brands by name

Popular brands

Samsung SRN-1000, User Manual

Search results

Summary of Contents for SRN-1000

Reviews:

Related manuals for SRN-1000

Brands by name

Popular brands