Samsung SRN-1000 User Manual Download Page 89

Page: 89 / 122

English

_89

●

enu Se

Tup

Live Streaming

You can configure the profile to transfer the live video of each channel via the network.

•

Profile : Select a network profile for the connected camera.

•

Codec : Show the codec information for the selected network profile.

•

Resolution : Display the resolution for the selected network profile.

•

Send Rate : Display the baud rate for the selected network profile.

•

Quality : Display the video quality for the selected network profile.

If the profiles used for network and recording are different, camera’s video feed may not comply with the frame rate as

specified in the camera.

e-mail

You can send an e-mail to a NVR-registered user at a specific time interval, or if an event occurs.

If the camera is set to <

OFF

> or the channel’s event is Video Loss, a notification is sent to the designated email address only

in text.

SmTp Setting

Sets the SMTP mail server.

•

Server Address : Displays the connected server type.

•

Port : Sets the communication port.

Summary of Contents for SRN-1000



























































































































Search results

Summary of Contents for SRN-1000

Reviews:

Related manuals for SRN-1000

Brands by name

Popular brands

Samsung SRN-1000, User Manual

Search results

Summary of Contents for SRN-1000

Reviews:

Related manuals for SRN-1000

Brands by name

Popular brands