Samsung SRN-1000 User Manual Download Page 34

Page: 34 / 122

34_

live viewer

Live SCreen ConfigurATion

System Status

You can check the status or operation of the NVR with the icons on the live screen.

Description

System

Operation

Displayed if there is a problem with the cooling fan.

HDD

Displayed if the HDD needs a technical examination.

Displayed if no HDD is installed or the existing HDD should be replaced.

Displayed if the HDD is full and the NVR has an insufficient space to

record.

Record

Appears when it is being recorded.

This is displayed if some channels will be recorded only on key frames

because the entire recording data size is over 100Mbps. (Page 76)

Displayed if a new firmware is found from the network.

Appears when recording is limited due to network overload.

Video Input

Status

Displayed if you press the Pause button.

Displayed if no input is entered in the condition that the camera is set to <

Displayed if no permission to live view is granted.

If your camera is turned <

OFF

> or in <

Covert

> mode, nothing is displayed on screen.

CAM 01

2013-01-01 09:54:36

Summary of Contents for SRN-1000



























































































































Search results

Summary of Contents for SRN-1000

Reviews:

Related manuals for SRN-1000

Brands by name

Popular brands

Samsung SRN-1000, User Manual

Search results

Summary of Contents for SRN-1000

Reviews:

Related manuals for SRN-1000

Brands by name

Popular brands