Samsung SRN-1000 User Manual Download Page 38

Page: 38 / 122

38_

live viewer

To switch to 16-split screen mode

Click <

The screen mode switches to 16-split screen mode which

displays the channel group including currently specified camera.

To switch to 36-split screen mode

Click <

The screen is switched to the 36-split mode, placing the

channel group including the selected camera among the

displayed channels at the top position.

To switch to 64-split screen mode

Click <

The screen is switched to the 64-split mode, placing the

channel group including the selected camera among the

displayed channels at the top position.

To go to your desired channel screen

Press the Previous/Next button to switch to the previous/next

channel group. Or click the channel selection bar next to Split

Mode buttons to select a desired channel in the drop-down

channel list.

Summary of Contents for SRN-1000



























































































































Search results

Summary of Contents for SRN-1000

Reviews:

Samsung SRN-1000, User Manual, Page: 38 / 122

Search results

Summary of Contents for SRN-1000

Reviews: