Samsung SRN-1000 User Manual Download Page 83

Page: 83 / 122

English

_83

●

enu Se

Tup

Setting the network Connection without router

•

Static

- Internet connection : Static IP, PPPoE, leased line, and LAN environments allows connection between the

NVR and remote user.

- NVR Network Settings : Set the <

interface

> in <

network

> menu of the connected NVR to <

Static

Consult your network manager for IP, Gateway and Subnet Mask.

•

dhCp

- Internet connection : Connect the NVR directly to a cable modem, DHCP, PPPoE modem or FTTH

network.

- NVR Network Settings : Set the <

interface

> in <

network

> menu of the connected NVR to <

dhCp

If IP is not assigned within 1 minute, it is set to the previous static IP.

•

pppoe

- Internet connection : An PPPoE modem is directly connected to the NVR, where the PPPoE connection

requires user ID and password.

- NVR Network Settings : Set the <

interface

> in <

network

> menu of the connected NVR to <

pppoe

PPPoE <

> and <

Password

> should be the same to the PPPoE user information.

If you don't know the ID and password, consult your PPPoE service provider.

Summary of Contents for SRN-1000



























































































































Search results

Summary of Contents for SRN-1000

Reviews:

Related manuals for SRN-1000

Brands by name

Popular brands

Samsung SRN-1000, User Manual

Search results

Summary of Contents for SRN-1000

Reviews:

Related manuals for SRN-1000

Brands by name

Popular brands