Samsung SRN-1000 User Manual Download Page 69

Page: 69 / 122

English

_69

●

enu Se

Tup

Connecting with iSCSi

If you connect NVR with an iSCSI device, you can search, connect and disconnect the iSCSI device.

•

IQN (iSCSI Qualified Name) : The iSCSI name which is named to the iSCSI protocol format is displayed.

•

Used/Total : The used capacity and the total capacity of the iSCSI device are displayed.

•

Status/Management : The status of the iSCSI device is displayed.

Supported products

Promise Technology vessRAID 1740i 1ea

registering an iSCSi device automatically

On the iSCSI screen, click <

Auto Add

On the Auto Add screen, enter the IP address and the connecting port, and click <

Click the device on the IQN list.

Enter the ID and the password, and click <

Summary of Contents for SRN-1000



























































































































Search results

Summary of Contents for SRN-1000

Reviews:

Related manuals for SRN-1000

Brands by name

Popular brands

Samsung SRN-1000, User Manual

Search results

Summary of Contents for SRN-1000

Reviews:

Related manuals for SRN-1000

Brands by name

Popular brands