Samsung SRN-1000 User Manual Download Page 68

Page: 68 / 122

68_

menu setup

•

No. : Shows the assigned number of the internal HDD.

To see the detailed positioning of the HDD according to the number, refer to <

HDD Map

•

Used/Total : Shows the used/total capacity of the storage device.

•

Usage : Sets the storage device's usage.

You can select the eSATA HDD for extended storage

If disconnected an extended eSATA HDD storage device while operating, the system may restart.

•

Status/Management : Display the status of the storage device.

•

Temperature : You can check the temperature of HDD installed in NVR.

•

HDD Map : Shows the internal HDD's locations according to assigned numbers.

Refer to this for servicing or additional HDD installation.

formatting

You can format a storage device.

•

No. : Select the check box of the device to format.

•

Used/Total : Shows the used/total capacity of the storage device.

•

Usage : Sets the storage device's usage.

•

Format : Select a device and press this to display the format confirmation dialog.

Press <

> to start formatting the selected storage device.

Note that formatting the device will delete all of the existing recording data.

Note that no recording is made during formatting is in progress.

Do never remove the device to format until formatting is completed.

Summary of Contents for SRN-1000



























































































































Search results

Summary of Contents for SRN-1000

Reviews:

Related manuals for SRN-1000

Brands by name

Popular brands

Samsung SRN-1000, User Manual

Search results

Summary of Contents for SRN-1000

Reviews:

Related manuals for SRN-1000

Brands by name

Popular brands