Samsung SMT-i5343 User Manual Download

Page: 88 / 201

Making LCD screen dark

Select

[Menu]



[Settings]



[Screen]



[LCD Dim]

- Screen dim: After 30 seconds/After 1 minute/

After 3 minutes

Making LCD screen dark-brightness

Select

[Menu]



[Settings]



[Screen]



[LCD Dim Level]

- Screen dim-brightness: Full/Low/Medium/High

LCD screen off

Select

[Menu]



[Settings]



[Screen]



[LCD Off]

Select the time when the LCD screen will be
turned off.

- Screen off: After 30 seconds/After 1 minute/

After 3 minutes/After 10 minutes/User Configuration

Changing the default settings for the screen menu may affect the lifetime of the
LCD and, therefore, do not change them if possible.

Below are shown the default LCD power settings.

- Screen dim: After 30 seconds

- Screen dim-brightness: Medium

- Screen off: User Configuration (08:00 to 18:00)

Using the LCD power setting function helps extend the lifetime of the LCD.

Summary of Contents for SMT-i5343










































































































































































































Search results

Summary of Contents for SMT-i5343

Reviews:

Related manuals for SMT-i5343

Brands by name

Popular brands

Samsung SMT-i5343, User Manual

Search results

Summary of Contents for SMT-i5343

Reviews:

Related manuals for SMT-i5343

Brands by name

Popular brands