Samsung SMT-i5343 Page 130 User Manual Download

Page: 130 / 201

128

Type

Function Description

No required value.

Usage

By pressing the button, you can cancel the call forward function.

DND

Function Description

When you press the button, there is no ringing although a call is
received. A message is played to the counterpart that the call cannot
be connected.

Settings

No required value.

Usage

You can enable/disable DND by pressing the button.

Recent
Outgoing
Redial

Function Description

Used to redial the most recent outgoing number.

Settings

No required value.

Usage

You can make a call to the most recent outgoing number by pressing
the button.

Recent
Incoming
Redial

Function Description

Used to redial the most recent incoming number.

Settings

No required value.

Usage

You can make a call to the most recent incoming number by pressing
the button.

Busy Forward

Function Description

You can enable/disable the function that enables a call to be
forwarded to a specific number when you are busy.

Settings

Enter a number for call forward.

Usage

You can enable/disable the Busy Forward by pressing the button.

Busy/No
Answer
Forward

Function Description

You can enable/disable the function that enables a call to be
forwarded to a specific number if there is an incoming call when you
are busy or if you do not pick up an incoming call.

Settings

Enter a number for call forward.

Usage

Summary of Contents for SMT-i5343










































































































































































































Search results

Summary of Contents for SMT-i5343

Reviews:

Related manuals for SMT-i5343

Brands by name

Popular brands

Samsung SMT-i5343, User Manual

Search results

Summary of Contents for SMT-i5343

Reviews:

Related manuals for SMT-i5343

Brands by name

Popular brands