Samsung SMT-i5343 Page 174 User Manual Download

Page: 174 / 201

172

Call related service

Call Forward

When a call is received, the call is forwarded to a specific number.

All Forward

All the calls are forwarded to a specific number.

You can enable/disable the all forward function as follows:

- Enable:

Dial ‘All Forward-Enable’ function code + Phone number used for

forwarding.

Disable: Dial ‘All Forward-Disable’ function code.

Busy Forward

A call is forwarded to a specific number only when you are busy.

You can enable/disable the busy forward function as follows:

Enable: Dial ‘Busy Forward-Enable’ function code + Phone number used for

forwarding.

Disable: Dial ‘Busy Forward-Disable’ function code.

No Answer Forward

A call is forwarded to a specific number when you do not pick up the phone.

You can enable/disable the no answer forward function as follows:

Enable: Dial ‘No Answer Forward-Enable’ function code + Phone number used for
forwarding.

Disable: Dial ‘No Answer Forward-Disable’ function code.

The no answer time can be specified in PWP.
If No Answer Forward is enabled by pressing the feature code on the phone, the
default time of 15 seconds is used.

Summary of Contents for SMT-i5343










































































































































































































Search results

Summary of Contents for SMT-i5343

Reviews:

Related manuals for SMT-i5343

Brands by name

Popular brands

Samsung SMT-i5343, User Manual

Search results

Summary of Contents for SMT-i5343

Reviews:

Related manuals for SMT-i5343

Brands by name

Popular brands