Samsung SMT-i5343 Page 49 User Manual Download

Page: 49 / 201

SMT-i5343 User Guide _

Under Video Call function

The video call function is available from V2.0 version or later.

Video Swap

During video call, if you press the

[Function]

soft

button and select

[Video Swap]

, you can switch

your video with the counterpart’s video.

Video Off

During video call, you can turn a video off by
pressing the

[Video Off]

soft button.

- If you press

[Video On]

at the bottom of screen, the

video off function is cleared.

- If you press

(screen zoom in) at the bottom of

screen, you can see the video call screen in full screen.
When you press

(screen zoom out), it returns

back to the default screen.

Summary of Contents for SMT-i5343










































































































































































































Search results

Summary of Contents for SMT-i5343

Reviews:

Related manuals for SMT-i5343

Brands by name

Popular brands

Samsung SMT-i5343, User Manual

Search results

Summary of Contents for SMT-i5343

Reviews:

Related manuals for SMT-i5343

Brands by name

Popular brands