Samsung SMT-i5343 User Manual Download

Page: 82 / 201

[AOM Button Setting]

To change the AOM button function, move to
a desired AOM button and press the

[OK]

button.

After moving to a desired AOM button by
using the navigation button, press the

[OK]

soft button.

Enter the information and press the

[Save]

soft button.

- If the entered information is not correct, the AOM

button function cannot be registered.

[Delete]

: You can delete a registered AOM button

function.

The AOM button setup function may not be available depending on system.
If this function does not work properly, contact the system administrator.
For detail information about how to use the AOM button function, refer to the SCM
operation manual.

Summary of Contents for SMT-i5343










































































































































































































Search results

Summary of Contents for SMT-i5343

Reviews:

Related manuals for SMT-i5343

Brands by name

Popular brands

Samsung SMT-i5343, User Manual

Search results

Summary of Contents for SMT-i5343

Reviews:

Related manuals for SMT-i5343

Brands by name

Popular brands