Samsung SMT-i5343 User Manual Download

Page: 84 / 201

[AOM Function/Operation]

Select an empty AOM button number and
press the

[Add]

soft button.

- You can move to a desired number in the AOM

device by pressing the number.

When you press the

[Key Select]

soft

button at the bottom of screen, the

[Please

Press AOM key]

popup window is

displayed. Press the corresponding number
of AOM device.

When you press the key of AOM device, the
below popup window is displayed at the
bottom of screen. In the popup window,
press the

[OK]

soft button.

Enter the information and press the

[Save]

soft button.

- If the entered information is not correct, the AOM

button function cannot be registered.

Summary of Contents for SMT-i5343










































































































































































































Search results

Summary of Contents for SMT-i5343

Reviews:

Related manuals for SMT-i5343

Brands by name

Popular brands

Samsung SMT-i5343, User Manual

Search results

Summary of Contents for SMT-i5343

Reviews:

Related manuals for SMT-i5343

Brands by name

Popular brands