Samsung OFFICESERV 500 Series Service Manual Download Page 81

Page: 81 / 113

OfficeServ 500 Wireless LAN Service Manual/Ed.00

CHAPTER 5. Maintenance

Page 5-5

1.2.2 Inquiry of Config & Status

With the selected [Config & Status] menu, the established value and status regarding
the LAN and the WLAN can be inquired.

Figure 5.3 Web screen for inquiring the WBS24 status (Config & Status)

Status items are shown below.

Up-Time : the passed time after booting

Booting Time : the final time of WBS24 booting

Version : Information on the WBS24 version

DASL Status : Connection status with the 8WLI

−

Deactive : Not activated status of the DASL line

−

Active(Not Config) : DASL line is activated, and the initialized message is
not received from the system.

−

Active(Config OK) : DASL line is activated, and the initialized message is
received from the system.

B-channel Status : the number of traffics being in use at present

Associated Nodes : Unavailable at present

Summary of Contents for OFFICESERV 500 Series


















































































































Search results

Summary of Contents for OFFICESERV 500 Series

Reviews:

Related manuals for OFFICESERV 500 Series

Brands by name

Popular brands

Samsung OFFICESERV 500 Series, Service Manual

Search results

Summary of Contents for OFFICESERV 500 Series

Reviews:

Related manuals for OFFICESERV 500 Series

Brands by name

Popular brands