Samsung OFFICESERV 500 Series Service Manual Download Page 47

Page: 47 / 113

OfficeServ 500 Wireless LAN Service Manual/Ed.00

CHAPTER 3. Installation

Page 3-5

2) Drill a hole at the ‘screw position’ illustrated in the <screw position diagram>.

The hole shall be at least 35mm deep and 5.5mm wide, which will enable the
plastic anchor to enter the hole easily.

Figure 3.4 Mounting the WBS24 on a Concrete Wall-Drilling a Hole

3) Detach the <screw position diagram> after drilling the hole.

4) Insert the plastic anchor into the hole using a hammer.

Figure 3.5 Mounting the WBS24 on a Concrete Wall-Inserting the Plastic Anchor

5) Insert a screw into the plastic anchor and tighten the screw with a cross-tip

screwdriver. Do not fully tighten the screw, but leave a gap of 5mm.

Figure 3.6 Mounting the WBS24 on a Concrete Wall-Tightening the Screw

Summary of Contents for OFFICESERV 500 Series


















































































































Search results

Summary of Contents for OFFICESERV 500 Series

Reviews:

Related manuals for OFFICESERV 500 Series

Brands by name

Popular brands

Samsung OFFICESERV 500 Series, Service Manual

Search results

Summary of Contents for OFFICESERV 500 Series

Reviews:

Related manuals for OFFICESERV 500 Series

Brands by name

Popular brands