Samsung OFFICESERV 500 Series Service Manual Download Page 39

Page: 39 / 113

OfficeServ 500 Wireless LAN Service Manual/Ed.00

CHAPTER 2. Hardware of OfficeServ 500

Page 2-3

LED

The LEDs are placed on the front side of WBS24(Combo) to show the status of
WBS24(Combo) equipment. The LED states are described in the following table.

Table 2.1 LED states of WBS24 (Combo)

LED Name

Function

Blue LED On

Blue LED Off

Blue LED Blinking

WLAN

Wireless LAN is
operating

Wireless LAN is
normally operating

Wireless LAN
is not operating

Data is
transmitted/received
through wireless LAN.

LAN

LAN is operating

LAN is normally
operating

LAN is
normally not
operating

Data is
transmitted/received
through LAN.

WLI

Connected with 8WLI

Normally
connected with
8WLI

Not connected
with 8WLI

Data is
transmitted/received
through the 8WLI
card and DASL line.

LD1

Indicating the B
channel in use.

Refer to the Table below.

LD2

Indicating the B
channel in use.

Refer to the Table below.

PWR

Power is on

Power is normally
supplied.

Power is not
normally
supplied.

Table 2.2 LD1 and LD2 states of WBS24 (Combo)

B channel No. on busy

States of LD1

States of LD2

Blue LED Off

Blue LED blinking periodically

Blue LED Off

Blue LED On

Blue LED Off

Blue LED On

Blue LED blinking periodically

Blue LED On

The status of WBS24(Combo)

Refer to ‘Chapter 5 Maintenance’ of this manual for how to inquire the status of
WBS24(Combo) through the LEDs in detail.

Summary of Contents for OFFICESERV 500 Series


















































































































Search results

Summary of Contents for OFFICESERV 500 Series

Reviews:

Related manuals for OFFICESERV 500 Series

Brands by name

Popular brands

Samsung OFFICESERV 500 Series, Service Manual

Search results

Summary of Contents for OFFICESERV 500 Series

Reviews:

Related manuals for OFFICESERV 500 Series

Brands by name

Popular brands