Samsung OFFICESERV 500 Series Service Manual Download Page 44

Page: 44 / 113

CHAPTER 3. Installation

OfficeServ 500 Wireless LAN Service Manual/Ed.00

Page 3-2

Mounting the 8WLI

Mount the 8WLI following the below instructions.

1) Prepare the 8WLI card.
2) Turn off the power of the OfficeServ 500

System and detach the front cover of

the OfficeServ 500

System using a screwdriver.

3) Mount the 8WLI card between slot 1 and slot 3 inside the cabinet. There are

guardrails attached at the top and bottom of the slot to fasten the 8WLI card.
Using these guardrails, carefully push the card into the system.

Figure 3.2 Mounting the 8WLI Card (1)

4) Firmly press the center of the card’s front panel to fully insert the 8WLI card into

the main board connector.

5) Once the 8WLI card is fully inserted into the main board connector, lower the

levers at the top and bottom of the slot inwards to fasten the card.

Summary of Contents for OFFICESERV 500 Series


















































































































Search results

Summary of Contents for OFFICESERV 500 Series

Reviews:

Related manuals for OFFICESERV 500 Series

Brands by name

Popular brands

Samsung OFFICESERV 500 Series, Service Manual

Search results

Summary of Contents for OFFICESERV 500 Series

Reviews:

Related manuals for OFFICESERV 500 Series

Brands by name

Popular brands