Samsung OFFICESERV 500 Series Service Manual Download Page 41

Page: 41 / 113

OfficeServ 500 Wireless LAN Service Manual/Ed.00

CHAPTER 2. Hardware of OfficeServ 500

Page 2-5

3 WBS24

(Basic)

The WBS24(Basic) is the AP for using the 2.4GHz wireless LAN service.

Front Side

The front side of WBS24(Basic) is shown below.

Figure 2.4 Front side of WBS24 (Basic)

LED

The LEDs are placed on the front side of WBS24(Basic) to show the status of
WBS24(Basic) equipment. The LED states are described in the following table.

Table 2.4 LED states of WBS24 (Basic)

LED Name

Function

Blue LED On

Blue LED Off

Blue LED Blinking

WLAN

Wireless LAN is
operating

Wireless LAN is
normally operating

Wireless LAN is
not operating

Data is
transmitted/received
through wireless LAN.

LAN

LAN is operating

LAN is normally
operating

LAN is normally
not operating

Data is
transmitted/received
through LAN.

WLI Connected

with

8WLI

Normally connected
with 8WLI

Not connected
with 8WLI

Data is
transmitted/received
through the 8WLI
card and DASL line.

LD1

Indicating the B
channel in use.

Refer to the Table 2.2

LD2

Indicating the B
channel in use.

Refer to the Table 2.2

PWR

Power is on

Power is normally
supplied.

Power is not
normally
supplied.

WLAN

LAN WLI LD1 LD2 PWR

Summary of Contents for OFFICESERV 500 Series


















































































































Search results

Summary of Contents for OFFICESERV 500 Series

Reviews:

Related manuals for OFFICESERV 500 Series

Brands by name

Popular brands

Samsung OFFICESERV 500 Series, Service Manual

Search results

Summary of Contents for OFFICESERV 500 Series

Reviews:

Related manuals for OFFICESERV 500 Series

Brands by name

Popular brands