Samsung OFFICESERV 500 Series Service Manual Download Page 19

Page: 19 / 113

OfficeServ 500 Wireless LAN Service Manual/Ed.00

CHAPTER 3. Installation

Page 1-3

The voice service is provided even in no-wired LAN environment.

The quality of service(QoS) is guaranteed using the exclusive voice path.

Since the OfficeServ 500

System supplies power remotely to the WBS24, no

separate electric wiring work is needed.

The transmission distance between the OfficeServ 500

System and the WBS24

is 600 meters, so the cell can be easily designed.

Since the built-in phone function is supported, a phone number can be assigned
instead of an IP address when registering a user.

The call path generation/maintenance and handover functions are provided.

The echo cancellation and voice codec(G.729, G.723.1) functions are provided.

The system supports the back-up battery, so the phone conversation can be
maintained during an electric failure.

Even if the ISM band is used, the VoIP is supported. So, there are almost no
interferences.

Easy upgrade

AP O & M function

Extension of the transmission distance

In case of the wired LAN, the transmission distance is only 100 meters in maximum.
To extend the distance, either hub or repeater is needed.

Summary of Contents for OFFICESERV 500 Series


















































































































Search results

Summary of Contents for OFFICESERV 500 Series

Reviews:

Related manuals for OFFICESERV 500 Series

Brands by name

Popular brands

Samsung OFFICESERV 500 Series, Service Manual

Search results

Summary of Contents for OFFICESERV 500 Series

Reviews:

Related manuals for OFFICESERV 500 Series

Brands by name

Popular brands