Samsung MagicLAN SWL-2000N User Manual Download Page 34

Page: 34 / 77

DNS Configuration

box will appear as follows. If you want to disable DNS, check on the

radio button for “

Disable DNS

”. Otherwise, check on the radio button for “

Enable DNS

” and

type

Host

and

Domain

in the proper field. After that, type IP Address of DNS server in “

DNS

Server Search Order

” box and click on “

Add

”. Repeat this procedures if multiple IP address

of the DNS server were provided. If applicable, fill out the “

Domain Suffix Search Order

”

field. Click on “

” at the bottom of “

TCP/IP Properties

” box.

“

System Setting Change

” box will appear as follows. Click on “

Yes

” to restart your

computer so that the whole installation procedures take effects.

Summary of Contents for MagicLAN SWL-2000N














































































Search results

Summary of Contents for MagicLAN SWL-2000N

Reviews:

Related manuals for MagicLAN SWL-2000N

Brands by name

Popular brands

Samsung MagicLAN SWL-2000N, User Manual

Search results

Summary of Contents for MagicLAN SWL-2000N

Reviews:

Related manuals for MagicLAN SWL-2000N

Brands by name

Popular brands