manualshive.com logo in svg

Samsung MagicLAN SWL-2000N, User Manual

Share
Download
Samsung MagicLAN SWL-2000N User Manual Download Page 51

50

13.

 

In “

Microsoft TCP/IP Properties

” box with 

DNS

 tab selected, enter the proper information for

the blanks. About the parameters and meaning, you can refer to the explanation in the previous section.

(3.5 Network Configuration Setup). If you are not sure about any of the required information in this

section,

please consult to your network administrator. Go to 

WINS Address

 tab.

          

14.

 

In “

Microsoft TCP/IP Properties

” box with 

WINS Address

 tab selected, select “

SAMSUNG

Wireless LAN Card

” and fill the rest of the blanks with the proper information. About the parameters

and meaning, you can refer to the explanation in the previous section. (3.5 Network Configuration Setup).

If you are not sure about any of the required information in this section, please consult to your network

administrator. Go to 

Routing

 tab.

Summary of Contents for MagicLAN SWL-2000N














































































Reviews:

No comments

Brands by name

Popular brands

Load more brands