Samsung MagicLAN SWL-2000N User Manual Download Page 45

Page: 45 / 77

23.

In “

Microsoft TCP/IP Properties

” box with

Routing

tab selected, make sure if “

Use IP

Routing

” is checked only if you want NT to play a role of router in your network. Click on “

”.

24.

When TCP/IP properties are set, click on “

Close

”. Then “

System Setting Change

” box will

appear as follows. Click on “

Yes

” to restart your computer so that the whole installation procedures take

effects.

4.2.2 When There is Windows NT networking already installed

1. Unlike Windows 95/98, since Windows NT does not support Plug and Play (PnP), you should

add your driver manually. To do so, click on “

start

” in task bar, go to “

Settings

”, and go to “

Control

Panel

”.

Under “

Control Panel

”, double click on

Network

icon.

Summary of Contents for MagicLAN SWL-2000N














































































Search results

Summary of Contents for MagicLAN SWL-2000N

Reviews:

Related manuals for MagicLAN SWL-2000N

Brands by name

Popular brands

Samsung MagicLAN SWL-2000N, User Manual

Search results

Summary of Contents for MagicLAN SWL-2000N

Reviews:

Related manuals for MagicLAN SWL-2000N

Brands by name

Popular brands