manualshive.com logo in svg

Samsung MagicLAN SWL-2000N, User Manual, Page: 63 / 77

Share
Download
Samsung MagicLAN SWL-2000N User Manual Download Page 63

62

•

 ACCESS POINT FEATURES

essid

: This field is used to name a wireless LAN group when in StructureNet mode. If the roaming is to be

supported, the value of ESS_ID of all the APs should be the same.

Default: wlan

ap_name

: This field is a string up to 9 letters and is used to give SWL-2000AP an identifier name. This is

useful if you have multiple APs on a network for roaming. In that case the essid for all APs should be same

but ap_name for each AP should be different.

Default: LocalAP

mode

: This field specifies the operating mode of the unit. Insert the “Instawave” for <Peer-to-Peer> and the

“StructureNet” for <StrectureNet>.

Default: StructureNet

protocol

: The normal mode of an AP is to pass all protocols. In this case the value of default protocol should

be “all”. If your wireless station uses TCP/IP protocol only, you can set the value of protocols to “TCP/IP”.

In this case, non TCP/IP messages are not passed by the AP.

Default: All

•

 TCP/IP PARAMETERS

IP_address

: This field is used to assign a TCP/IP address to the AP and needed when a user manages the AP

by TELNET or uses web manager utilities. A user can access management utilities for the AP by putting in

the assigned IP address on TELNET or WEB BROWSER.

Default: 0.0.0.0 

(No IP address assigned)

subnet_mask

: This field is used to define the TCP/IP sub-net mask. This field should be set if you plan to

use the built in management features of the AP.

Default: 255.255.255.0

gateway

: This field is needed to connect to an external network using the TCP/IP protocol. SWL-2000AP

stores all the IP addresses received from TCP/IP ARP (Address Resolution Protocol) message.  If the

destination is an IP address instead of a local network, the packets are sent to a gateway.

Default: 0.0.0.0 (no gateway)

•

 MANAGEMENT FUNCTIONS

password

: This field allows the manager to define the password used by the Command Line Manager before

they can enter commands.

Default: “default”

telnet

: This field enables or disables the built TELNET management capability. This field will not affect a

terminal attached via the serial port, which is always enabled when a terminal is attached. You can select

either “on” or “off” to enable or disable it.

Default: on

Summary of Contents for MagicLAN SWL-2000N














































































Reviews:

No comments