Samsung MagicLAN SWL-2000N User Manual Download Page 44 | Manualshive

Page: 44 / 77

background image

43

22.

In “

Microsoft TCP/IP Properties

” box with

WINS Address

tab selected, select SAMSUNG

Wireless LAN Card (PCMCIA) and fill the rest of the blanks with the proper information. About the

parameters and meaning, you can refer to the explanation in the previous section. (3.5 Network

Configuration Setup). If you are not sure about any of the required information in this section, please

consult to your network administrator. Go to

Routing

tab.

«
...
42
43
44
45
46
...
»

Summary of Contents for MagicLAN SWL-2000N














































































Reviews:

No comments

Related manuals for MagicLAN SWL-2000N

Brand: D-Link Pages: 43

PoE Injector Adapter POE-32001T

Brand: UNICOM Pages: 1

Brand: ID Systems Pages: 12

Brand: Telex Pages: 6

Nano Bluetooth USB-Adapter

Brand: Hama Pages: 26

Brand: RocketFish Pages: 15

Phoenix Window Adapter

Brand: Therma-Stor Pages: 4

Brand: DeLOCK Pages: 16

Brand: ZyXEL Communications Pages: 67

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

XA-118 Marketing

Brand: Sony Pages: 1

XA-120iP Operating Instruccions

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 16

Brand: Sony Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands