8
GB
Pos: 4.7.13 /Innenteil/Sicherheitsvorschriften/Wartung und Lagerung/Österreich @ 0\mod_1125474640679_1521.doc @ 1644 @ @ 1
•
Notes for Austria:
The socket coupler of the connecting cable must be splashproof.
Pos: 5.1 /---------- 1 Leerzeile ---------- @ 0\mod_1114611787140_1521.doc @ 2070 @ @ 1
Pos: 5.2 /Innenteil/Beschreibung der Bauteile/1 BESCHREIBUNG DER BAUTEILE @ 0\mod_1115187892468_1521.doc @ 1664 @ 1 @ 1
6
DESCRIPTION OF COMPONENTS
Pos: 5.3 /Innenteil/Beschreibung der Bauteile/Beschreibung der Bauteile 32-EL Text @ 23\mod_1373884770755_1521.doc @ 177103 @ @ 1
1 Actuating grip for motor (safety grip)
2 Cable connection plug
3 Ejection
flap
4 Electric motor hood
5 Handle for adjusting the height
6 Motor
bracket
7 Strain relief device for electric cable
8 Cable
guide
9 Casing on the upper part of the bar
10 Locking button (red)
Pos: 6.1 /---------- 1 Leerzeile ---------- @ 0\mod_1114611787140_1521.doc @ 2070 @ @ 1
Pos: 6.2 /Innenteil/Vorbereitende Arbeiten/1 VORBEREITENDE ARBEITEN @ 0\mod_1115194917734_1521.doc @ 1672 @ 1 @ 1
7
PREPARATION
Pos: 6.3 /Innenteil/Vorbereitende Arbeiten/Vorbereitende Arbeiten Text Elektromäher 32er @ 11\mod_1256287655269_1521.doc @ 96553 @ @ 1
The following parts are included in the packaging for assembly of the mower:
• Mower
• Pre-assembled
handlebar upper section
•
Handlebar lower section
•
Collecting bag, collecting bag frame, chute
•
Tool bag with the following contents:
– Operator's manual with Declaration of Conformity
– Warranty conditions and Warranty card
– Various fixing parts (strain relief fitting, flat-head screw, cable guide, washers, wing-nuts, cheese head screws,
cable tie).
In the unlikely event of a missing part, please contact your dealer.
Pos: 6.4 /Innenteil/Vorbereitende Arbeiten/1.1 Führungsholm-Unterteil anbauen (Abbildung S3 + C1 ) @ 3\mod_1157113823523_1521.doc @ 18609 @ 2 @ 1
Assembling the handlebar lower section (Ilustration S3 +
C1
)
Pos: 6.5 /Innenteil/Vorbereitende Arbeiten/Führungsholm-Unterteil anbauen Text Elektromäher 32er @ 3\mod_1157114682427_1521.doc @ 18629 @ @ 1
Before assembling the handlebar lower section, the strain relief device (1) (from the tool box) must first be fitted over the
handlebar lower section
S3
.
– Insert the ends of the bars as far as they will go into the two holes on the right and left of the body
C1
.
– Insert the two screws from below and tighten with a srewdriver.
Pos: 6.6 /Innenteil/Vorbereitende Arbeiten/1.1 Führungsholm-Oberteil anbauen (Abbildung E1 ) @ 3\mod_1152273526917_1521.doc @ 17295 @ 2 @ 1
Assembling the handlebar upper section (Illustration
E1
)
Pos: 6.7 /Innenteil/Vorbereitende Arbeiten/Führungsholm-Oberteil anbauen Text Elektromäher 32er @ 3\mod_1157115188951_1521.doc @ 18639 @ @ 1
– The safety grip for motor is pre-assembled on the upper handle and the cable to the electric motor is attached here.
– Fit the handlebar upper section to the lower section at right and left, so that the attachment holes of both sections are in
alignment.
– Insert the flat-head screw inwards on the left hand side, and the cable guide inwards on the right hand side and screw
both handlebar sections together on the inside using a washer and a wing-nut.
– Place the cable into the cable guide. This prevents trapping of the cable when folding the handlebar.
– Attach the cable to the lower handlebar section using the cable tie from the toolbag. When folding the upper handlebar
section, ensure that the cable is not trapped.
Pos: 6.8 /Innenteil/Vorbereitende Arbeiten/1.1 Grasfangsack zusammenbauen und am Mäher einhängen (Abbildung Q1 + R1 + S1) @ 3\mod_1157114106653_1521.doc @ 18619 @ 2 @ 1
Assemble the collecting sack and hang it onto the mower (Illustration Q1 + R1 + S1 )
Pos: 6.9 /Innenteil/Vorbereitende Arbeiten/Grasfangsack zusammenbauen und am Mäher einhängen Text 32er @ 3\mod_1157115817409_1521.doc @ 18649 @ @ 1
– Turn the chute (1) outwards and push fully down
Q1
.
– First insert the grass bag frame with the clip forward into the grass bag. Align the upper seams of the bag with the clip.
– Press the retaining profiles of the collecting sack onto the bars of the collecting sack frame
R1
.
– Press the chute (1) on to the collecting sack frame from above
Q1
.
– Open the ejection flap of the mower upwards.
– Pick up the collecting sack by the carrying strap, place the chute (1) at the collecting sack opening into the ejection flap
and hang it in the mower casing with its two side hooks upwards
S1
.
– Attach ejection flap to collector.