Russound CAM6.6X-S1 Instruction Manual Download Page 18

Page: 18 / 116

Category Search Mode (

1..C

T S

)

XM Radio is organized by Channel Category (e.g.,

Rock, Country, News

). Within each category is

a series of channels (e.g., Top Tracks, Bluegrass Junction, XM Classics). Channel selection in this
mode is refined to scrolling only those channels in the selected category.

Next Category

This button press accesses the next category from the current category.

Previous Category

This button press accesses the previous category from the current category.

Category Channel Up

This button press accesses the next channel up within the selected category.

Category Channel Down

This button press accesses the next channel down within the selected category.

UNO-S1

UNO-S2

UNO-LRC1

Category Search Mode

Next Category

Previous Category

Category Channel Up

Hold

Category Channel Down

Hold

USER

INTERNAL SOURCE - XM TUNER

XM Radio Modes

Summary of Contents for CAM6.6X-S1




















































































































Search results

Summary of Contents for CAM6.6X-S1

Reviews:

Related manuals for CAM6.6X-S1

Brands by name

Popular brands

Russound CAM6.6X-S1, Instruction Manual

Search results

Summary of Contents for CAM6.6X-S1

Reviews:

Related manuals for CAM6.6X-S1

Brands by name

Popular brands