Russound CAM6.6X-S1 Instruction Manual Download Page 20

Page: 20 / 116

UNO-S1 Keypad Control of Tuner

Selecting the tuner

On the UNO-S2 keypad, press

to select the

XM Tuner by choosing the tuner’s preassigned

source number (1).

Selecting the desired channel

Press and hold

and

to activate manual

channel selection. Once active, press

to scroll through channels. The channel will

scroll twice on the keypad then stop and display

the channel display format’s first five characters.

If an XM radio tuner operation does not
specifically refer to an UNO-S1 button
operation, use the UNO-LRC1 remote con-
trol to transmit commands through the
UNO-S1.

USER

INTERNAL SOURCE - XM TUNER

UNO-S1 Keypad Control

TUNER SELECTION - Select
source number assigned to
XM Tuner (1)

CHANNEL SELECTION -
Scrolls through channels
(press and hold, then
press)

Blues

Summary of Contents for CAM6.6X-S1




















































































































Search results

Summary of Contents for CAM6.6X-S1

Reviews:

Related manuals for CAM6.6X-S1

Brands by name

Popular brands

Russound CAM6.6X-S1, Instruction Manual

Search results

Summary of Contents for CAM6.6X-S1

Reviews:

Related manuals for CAM6.6X-S1

Brands by name

Popular brands