Russound CAM6.6X-S1 Instruction Manual Download Page 25

Page: 25 / 116

INSTALLER SECTION

Getting Started

Includes an installation overview, including tools needed and wiring instructions.

Component Guides

Reviews front and back panel features of the CAM6.6 controller and the UNO-S1 and UNO-S2
keypads.

Keypad Installation

Explains UNO-S1 and UNO-S2 keypad installation and wiring.

Making Connections

Details front and back panel connections of the controller and the keypad.

System Programming Overview

Outlines the programming planning process, and includes information forms to complete prior to
programming.

Installation Menu

Explains the programming menus that set up controller, keypad, source and zone operations.

Setup Menu Flow Charts

Presents the programming menus in a graphical flow chart format.

IR Device Codes

A list of controller’s IR device code library for source Device Code entries.

Key Function Codes

A list of IR codes for each command type contained in the built-in library.

Source Names

A list of Source Names available for assignment.

Sample Configurations

Diagrams of various configurations using CAM6.6s and other components.

Summary of Contents for CAM6.6X-S1




















































































































Search results

Summary of Contents for CAM6.6X-S1

Reviews:

Related manuals for CAM6.6X-S1

Brands by name

Popular brands

Russound CAM6.6X-S1, Instruction Manual

Search results

Summary of Contents for CAM6.6X-S1

Reviews:

Related manuals for CAM6.6X-S1

Brands by name

Popular brands