Russound CAM6.6X-S1 Instruction Manual Download Page 55 | Manualshive

Page: 55 / 116

background image

55

1. BUILD TIME

Displays the firmware Build Time of the tuner.

(BTime)

2. BUILD DATE

Displays the firmware Build Date of the tuner.

(BDate)

3. VERSION

Displays the firmware version of the tuner.

(Ver)

SOURCE SETUP (SrcSu)

Source Setup allows the system’s sources to be configured.

The following items can be found in the SOURCE SETUP menu:

BASIC SETUP (BasSu)

KEY CONFIG (KeyCf)

SOURCE NAMES (SrcNm)

SRC VOL TRIM (SrcVT)

NUMERIC IR (NumIR)

SRC SEL CMD (SrcSC)

# OF SOURCES (#Srcs)

BASIC SETUP (BasSu)

NOTE: The BASIC SETUP procedure should be performed for each source before proceeding to other
source setting changes.

NOTE: If the CAM6.6 has an optional internal source installed, it is pre-configured as Source 1, with
source name <XM> and command type Peripheral.

This procedure uses built-in source “templates” to quickly and easily configure the source settings
needed for basic operation of the source component. Before performing BASIC SETUP, connect the
source components to the CAM6.6 as outlined in the Source Connections section. Also be sure that
all sources are powered on.

See Basic Setup - Flow Chart 69

1. SOURCE NUM

–

Select the source to be configured.

(Src #)

2. SOURCE NAME

–

Select the name for the source (e.g., DVD, Aux 2, Jazz, etc.).

(Name)

3. COMMAND TYPE

–

Select the type of command template (e.g., CD, TV, etc.). Selecting

(CmdTp)

the command type template will tell the CAM6.6 how to configure the
key’s command and text for the source component.

INSTALLER

INSTALLATION MENU

«
...
53
54
55
56
57
...
»

Summary of Contents for CAM6.6X-S1





















































































































Reviews:

No comments

Related manuals for CAM6.6X-S1

Brand: NAD Pages: 14

Brand: HAMTRONICS Pages: 11

Brand: Sylvania Pages: 8

Brand: Blaupunkt Pages: 2

Brand: Alinko Pages: 48

Brand: JDM Pages: 8

Brand: Ten-Tec Pages: 147

Brand: IFR Systems Pages: 204

Brand: Z-Wave Pages: 2

Brand: Omnex Pages: 16

Brand: Denon Pages: 15

Brand: Team Electronic Pages: 27

Brand: Daewoo Pages: 125

Brand: Jensen Pages: 103

AM-FM Receiver 870-20

Brand: Raymer Pages: 4

Brand: AMIMON Pages: 56

Brand: Lafayette Pages: 30

Brand: Dish Network Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands